Safety and PPE Items are Available

Order Now

Danby Air Conditioner Troubleshooting

Occasionally, a problem may arise with your Danby air conditioner that is minor in nature. There are some common Danby AC problems and solutions that can be attended to and completely fixed without any help from a specialist. To help you, here, we have given about Danby air conditioner troubleshooting with possible solutions. However, having your AC go down during summer is an unfortunate event that needs to be addressed quickly.

Table of Contents

1. Danby Air Conditioner Troubleshooting Guide

2. Danby Air Conditioner Won’t Turn ON

3. Air Conditioner Not Cooling Enough

4. Noise in Danby Air Conditioner

5. Water Dripping from AC

6. Frost Buildup in the Unit

7. Summing-Up

Danby Air Conditioner Troubleshooting Guide

Find the possible solutions to fix the problems of Danby air conditioner in an easy way without any extra charges for a technician.

Buy OEM Danby Air Conditioner Parts @ PartsIPS.

Danby Air Conditioner Won’t Turn ON

Check the power cable of your air conditioning unit as it may not power on. Although, verify if it is connected to an electrical outlet or not.

Next, check the power supply cord functioning whether it is doing correctly or not. Locate the two buttons on the power cord plug head, one is labeled with "Test" and the other indicates "RESET". If you click on the TEST button, the RESET button needed to be pop out. Then, press the RESET button and the cord should be energized with power when it is plugged into the outlet.

If still, your AC is not running, you will have to inspect the circuit breakers inside the electrical panel. Normally, it is placed in the basement, utility room or attic. Once reset the breakers by turning them off and on back.

Air Conditioner Not Cooling Enough

If you feel that your air conditioner has poor cooling power, then turn it off for 5 minutes and then turn it back ON. If the AC still not cooling enough, access the filter by grasping the sides of the front grille and pulling it forward. Once you have found the air filter, remove it. Next, attach a soft brush to your vacuum and brush the air filter.

If the filter is dirty, you need to wash it with a mild detergent in lukewarm water below 10 degrees F. After that, rinse the water filter in clean water and let it down for drying. If it was dried, you can reinsert the air filter in your Danby AC.

In addition to the above, you need to check certain conditions to get proper cooling from your AC.

  • Check if the windows/ doors in the room are not closed properly. Make sure all doors and windows are closed properly.
  • There might be heat sources inside your room. Remove them if possible if there are any.
  • Exhaust air duct is not connected or blocked - If so, connect the duct and ensure that it functioning correctly.
  • The temperature setting might be at too high. Try to decrease the set temperature.

Danby AC Replacement Parts - Order Online!

Noise in Danby Air Conditioner

If there are any loose parts in your Danby, they may be caused to noise. So, first, you should examine for the loosen parts. Tighten the screws if you found that the cover panel is loose. If parts or components are loose on other components, tighten them as well.

Once all Danby air conditioner parts are secured, check inside the grille for any debris accumulated. Because sometimes particles and objects may find their way into the air conditioner and rattle around the fan area. Hence, inspect the fan as well. You should turn off the power to the unit before checking the fan.

Also, check if the ground is not leveled or not flat enough. Your AC should be placed on flat and level ground.

Fast Shipping on Danby Parts - Shop for your Air Conditioners.

Water Dripping from AC

If your Danby AC is producing a foul odor, you can place an algicide tablet in the base panel. With the formation of mildew or mold on wet surfaces, odors might have occurred. Take a dry lint-free cloth to wipe off the water if the unit is wet.

You will have to check the installation of your Danby air conditioner if water is dripping inside. AC can drip water if it is not angled properly to allow water to drain outside. So, check the correct installation instructions in the Danby manual for your unit's specific model.

Frost Buildup in the Unit

When the AC has frost or ice buildup, you need to switch the mode from AC to FAN. Leave the unit in the FAN model until the ice melts completely. Normally, ice or frost will form if the outdoor temperature is approximately 65 degrees Fahrenheit. And, check the air filter for dirt and clean it if necessary.


That’s all about a few of Danby air conditioner problems and their troubleshooting tips. Unfortunately, we could not cover your specific problem in this post. However, check your owner’s manual for getting more detailed solutions on Danby AC troubleshooting.

Related COntent:

1. Danby Dcf401w Troubleshooting 2. Danby Portable Washer Troubleshooting

3. Danby Refrigerator Troubleshooting  4. LG Air Conditioner Troubleshooting

Leave your comment

Preset Color